Home  >  Cast Iron Burners

 

Cast Iron Burners

Tejas Smokers® sells High Pressure cast iron propane burners, manufactured using our own casting moldsOutdoor cookers normally use high pressure burners because they give you much higher heat output than a low pressure burner.   Each one of our cast burners, pipe burners (also referred to as stick burners and tube burners), and jet burners are bench tested and optimized for maximum gas flame efficiency and trouble-free operation before shipping to the customer.  We know of no other burner vendor doing this.  Free shipping to the 48 contiguous U.S. States.  


Tejas Smokers®  Low Pressure cast burners require either natural gas or a low pressure propane gas regulator if your fuel source is directly from a propane tank bottle. Propane supplied in a trailer home or RV normally has the propane gas already adjusted to a very low pressure at the propane source. LOW PRESSURE burners give a little more heat than that of a gas stove top burner in the kitchen. Preset LOW PRESSURE propane regulators are set at 6 ounces. Natural gas pressure in most areas is fixed at 10 ounces, or less, and requires only a variable on/off valve to attenuate the flame.

 

HPOCA4 - High Pressure Cast Iron Burner with 4" Neck

  HPOCA4

HPOCA4 - High Pressure Cast Iron Burner with 4" Neck.

●  Produces up to 160,000 BTU/hr in an evenly-directed manner.
●  Comes with an air shutter, Insect Guard, and a 90° 3/8" flare Orifice.
    Alternatively, a 180° 3/8" flare orifice fitting is also available.
●  Best working distance is 3" to 4" from top of cast to bottom of pot.

●  The center bolt is a 6mm in diameter or a 1/4".
  From the center bolt to the air inlet at the edge of the burner is 5".
●  From the center bolt to the end of the orifice is approximately 6".
●  Total length of the burner with an orifice is approximately 8".
●  Burner head diameter is 4", height from base to top of burner is 3".

●  We recommend the use of a COM3 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.


Weight 3# 1 oz. Free shipping within the 48 contiguous U.S. States. 

HPOCA4 with Optional Control Valve Orifice
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck


Bottom side view of the HPOCA4
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck

 

$34.95

 

 

HPB6 - High Pressure Cast Iron Burner with 6" Neck

  HPB6

HPB6 - High Pressure Cast Iron Burner with 6" Neck.

●  Produces up to 160,000 BTU/hr in an evenly-directed manner.
●  It comes with an air shutter, Insect Guard and a 90° 3/8" flare Orifice.
    
Alternatively, a 180° 3/8" flare orifice fitting is also available.
●  Best working distance is 3" to 4" from top of cast to bottom of pot.

●  The center bolt is a 10mm in diameter.
  From the center bolt to the air inlet at the edge of the burner is 6 1/4".
●  F
rom the center bolt to the end of the orifice is approximately 7 1/2".
●  Total length of the burner with an orifice is approximately 10".
●  Burner head diameter is 4", height from base to top of burner is 3".
 

●  We recommend the use of a COM3 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.


Weight 3# 1 oz. Free shipping within the 48 contiguous U.S. States. 
 

HPB6 with Optional Control Valve Orifice
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck


Bottom side view of the HPB6
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck

 

 

$34.95

 

 

HPCAST6 - High Pressure Cast Iron Burner with 6" Neck

  HPCAST6

HPCAST6 - High Pressure Cast Iron Burner with 6" Neck.

●  Produces up to 160,000 BTU/hr in an evenly-directed manner.
●  It comes with an air shutter, Insect Guard and a 90° 3/8" flare Orifice.
    Alternatively, a 180° 3/8" flare orifice fitting is also available.
●  Best working distance is 3" to 4" from top of cast to bottom of pot.

●  The center bolt is a 6mm in diameter or a 1/4".
   From the center bolt to the air inlet at the edge of the burner is 6 1/2".
●  From the center bolt to the end of the orifice is approximately 7 1/2".
●  Total length of the burner with an orifice is approximately 10".
●  Burner head diameter is 4", height from base to top of burner is 3".

●  We recommend the use of a COM3 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.


Weight 3# 3 oz. Free shipping within the 48 contiguous U.S. States. 


HPCAST6 with Optional Control Valve Orifice
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck


Bottom side view of the HPCAST6
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck
  • 160,000 BTU/hr High Pressure Cast Iron Burner with 4in Neck


Pilot Light Assembly is available as an Option at additional charge (Go to bottom of page)
  • 160,000 BTU/hr High Pressure Cast Iron Burner with Pilot Assembly
  • 160,000 BTU/hr High Pressure Cast Iron Burner with Pilot Assembly

 

$34.95

 

 

HPGX-1 Cast Iron Venturi Only

  HPGX-1

HPGX-1  3/4" Cast Iron Venturi Only

●  Venturi permits good efficiency in the air and gas mixing.

●  May be used in conjunction with a black drilled pipe nipple
    that is capped off (known as a pipe burner) or in a variety of special
    applications where the air and gas mixture is delivered to a burner.


●  It has a 3/4" Female Normal Pipe thread outlet.

●  The flat top surface is 3" in diameter by 1 1/2" in height.
●  The height of the venturi with an orifice is approximately 3".

●  It comes with an air shutter, Insect Guard and a 90° 3/8" flare Orifice.
    Alternatively, a 180° 3/8" flare orifice fitting is also available. Ask.

●  For High Pressure use we recommend the COM3 regulator/hose.
●  For Low Pressure use we recommend the COM5 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.

●  Shipped with a #61 orifice for High Pressure Propane, OR specify
    your fuel;  we will custom drill your orifice at no extra charge.



Weight 12 oz. Free shipping within the 48 contiguous U.S. States.  

  • 3/4in Female NPT Cast Iron Venturi
    3/4" Female NPT
  • 3/4in Female NPT Cast Iron Venturi
    HPGX-1 with Optional Control Valve Orifice

 

$29.95

 

 

HPGX-2 - High Pressure Two-Part Cast Iron Burner - Adjustable Length Neck

  HPGX-2

HPGX-2 - Two-Part Cast Iron Burner with Adjustable Length Neck.

●  Produces up to 160,000 BTU/hr in an evenly-directed manner.
  Burner is ideal for applications where venturi is placed outside or
    farther away from the area where the burner is installed.

  Distance between burner head and venturi is determined by the   
    length of 3/4" black pipe nipple used.  P
ipe nipple is NOT included.
●  Best working distance is 3" to 4" from top of cast to bottom of pot.

●  Burner head and venturi have 3/4" female normal pipe thread inlets.
●  Comes with air shutter, Insect Guard, and a 90° 3/8" flare Orifice
    A 180° 3/8" flare fitting is also available upon request.  Ask.
●  The center bolt is a 10mm in diameter in the burner head.
●  Burner head diameter is 4", height from base to top of burner is 3".

●  We recommend the use of a COM3 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.

●  HPGX-2 Video



 Weight 3# 10 oz. Free shipping within the 48 contiguous U.S. States.


HPGX-2 with Optional Control Valve Orifice
  • 160,000 BTU/hr Two-Part Cast Iron Burner with Adjustable Length Neck
  • 160,000 BTU/hr Two-Part Cast Iron Burner with Adjustable Length Neck


  • 160,000 BTU/hr Two-Part Cast Iron Burner with Adjustable Length Neck
    Bottom side view of the HPGX-2
  • 160,000 BTU/hr Two-Part Cast Iron Burner with Adjustable Length Neck
    HPGX-2 Performance

 

$59.95

 

 

HPMAX-1 Cast Iron MONSTER Venturi Only

  HPMAX-1

HPMAX-1    1 1/4" Cast Iron MONSTER Venturi Only

●  Venturi has extra large volume that permits great efficiency in
    the air and gas 
mixing.

●  May be used in conjunction with a black drilled pipe nipple
    (pipe burner) that is capped off or in a variety of special applications
    where the air and gas mixture is delivered to the burner.


●  It has a 1 1/4" Female Normal Pipe thread outlet.
●  The flat top surface is 4" in diameter by 2 1/2" in height.
●  The height of the venturi with an orifice is approximately 4".

●  It comes with an air shutter, Insect Guard and a 90° 3/8" flare Orifice
    Alternatively, a 180° 3/8" flare orifice fitting is also available.  Ask.

  For High Pressure use we recommend the COM3 regulator/hose.
●  For Low Pressure use we recommend the COM5 regulator/hose.

●  Also available with an Optional Needle Control Valve with Orifice.

●  Shipped with #61 orifice for High Pressure Propane , or drilled to
    custom orifice size depending on your fuel.  No extra charge.

 

Weight 2# 2 oz. Free shipping within the 48 contiguous U.S. States.

 

  • 1 1/4in Female NPT Cast Iron MONSTER Venturi
    1 1/4" Female NPT
  • 1 1/4in Female NPT Cast Iron MONSTER Venturi
    HPMAX-1 with Optional Control Valve Orifice

 

$68.95

 

 

HPMAX-2 - High Pressure  MONSTER 2-Part Burner - Adj. Length Neck

  HPMAX-2

HPMAX-2 -  MONSTER Two-Part Cast Iron Burner with
Adjustable Length Neck.


 Produces up to 225,000 BTU/hr in an evenly-directed manner.
  This monster unique burner is ideal for applications where the venturi is
    placed outside or farther away from the area where the burner is placed

  Distance between burner head and venturi determined by length of the
    1 1/4" black pipe nipple used
.  Pipe nipple is NOT included.

●  Best working distance is 5" to 6" from top of cast to bottom of pot.

   Burner head and venturi have 1 1/4" female normal pipe thread inlets.
   It comes with an air shutter, Insect Guard, and a 90° 3/8" flare Orifice.
     A 180° 3/8" flare fitting is also available.  Ask.  No extra charge.

   The center bolt is a 10mm in diameter in the burner head.
●   Burner head diameter is 6", height from base to top of burner is 6".

●   We recommend the use of a COM3 regulator/hose.
●   Also available with an Optional Needle Control Valve with Orifice.


Weight 9# 6 oz. Free shipping within the 48 contiguous U.S. States.


 

  • 225,000 BTU/hr MONSTER Two-Part Cast Iron Burner with Adjustable Length Neck
    HPMAX-2 with Optional CVO250
  • 225,000 BTU/hr MONSTER Two-Part Cast Iron Burner with Adjustable Length Neck
    Bottom side view of the HPMAX-2
Comparative flame outputs of the HPMAX-2 and the HPGX-2
  • Comparative flame outputs of the HPMAX-2 and the HPGX-2
  • Comparative flame outputs of the HPMAX-2 and the HPGX-2

 

$144.95

 

 

PBM125 - Pipe Burners - (support LEGS are an option)

  PBM125

PBM125 - Straight Pipe Burner 1 1/4" ID in 32", 44", 56", or 68" lengths

●   We stock 32", 44", 56", and 68" pipe burner assemblies, also called
     stick burners or tube burners, (as measured from one end of the
     pipe to the opposite end of the pipe's threads.)

●   The pipe burners are 1.25"ID and 1.5"OD with a standard schedule
     40 pipe wall thickness.  These assemblies include a welded end cap
     at one end and a venturi at the other end. 

●   For supporting the assembly we recommend a cradle out of a well
     supported length of angle iron.  A cradle support will permit easy
     removal of the burner unit for cleaning, when necessary.

●   Our pipe burners have been engineered and tested to give a even,
     high heat blue flame across the length of the pipe and they easily light.
●   The first 8" of the pipe is used as the "throat" of the burner and does
     not have any holes for flames. This space is required for the air and            gas to mix efficiently in order to have a nice blue flame.  Don't waste          propane using a pipe burner that burns an inefficient yellow flame.


●   Pipe Burners can be run by High Pressure Propane, Low Pressure
     Propane, or Natural Gas.
●   For High Pressure use we recommend the COM3 regulator/hose.
●   For Low Pressure use we recommend the COM5 regulator/hose.
●   Also available with an Optional Needle Control Valve with Orifice.


●  Pipe Burner Video

                                                       
                                                          Weight    Weight w/LEGS
●   PBM125-32" has 24" of flame         8#                  10#
●   PBM125-44" has 36" of flame       10#                  12#
●   PBM125-56" has 48" of flame       12#                  15#
●   PBM125-68" has 60" of flame       15#                  18#

If you would like  TejasSmokers.com  to weld permanent 1/2" diameter round support legs along the length of your pipe burner then order the unit with "LEGS" at the end of the part number, as shown in the drop down box to the right.


Free shipping within the 48 contiguous U.S. States.

 

  • 68in Pipe Burner with 1 1/4in FNPT Venturi and Optional Control Valve Orifice
    68" Pipe Burner with 1 1/4" FNPT Venturi and Optional Control Valve Orifice (Needle Valve)
  • 32in Pipe Burner with Support Legs
    32" Pipe Burner with Optional Support Legs
  • 32in Pipe Burner with Optional Support Legs and Pilot Assembly   32in Pipe Burner with Optional Support Legs and Pilot Assembly
    Pilot Light Assembly is available as an Option at additional charge (Go to bottom of page)

    If you would like to automate your pipe burner or any cast iron burner setup so that it uses a pilot light or piezo electric ignitor and is controlled by the temperature you set, then give us a call at 713.222.0077.   We can help you do it.

 

$219.95

 

 

PBMG125 - Pipe Burner with Grease Shield - (support LEGS are an option)

  PBMG125

PBMG125 - Straight Pipe Burner 1 1/4" ID in 32", 44", 56", or 68" lengths
with a permanently welded 3" high grease shield.


●   We stock 32", 44", 56", and 68" pipe burners assemblies.(As measured

     from one end of the pipe to the opposite end of the pipe's threads.)

●   The pipe burners are 1.25"ID and 1.5"OD with a standard schedule

     40 pipe wall thickness.  These assemblies include a welded end cap

     at one end and a venturi at the other end.  

●   For supporting the assembly we recommend a cradle out of a well

     supported length of angle iron.  A cradle support will permit easy

     removal of the burner unit for cleaning, when necessary.

  

●   Our pipe burners have been engineered and tested to give a even,

     high heat blue flame across the length of the pipe and they easily light. 

●   The first 8" of the pipe is used as the "throat" of the burner and does

     not have any holes for flames. This space is required for the air and            gas to mix efficiently in order to have a nice blue flame.  Don't waste          propane using a pipe burner that burns an inefficient yellow flame.

●   For High Pressure we recommend the COM3 regulator/hose.

●   For Low Pressure use we recommend the COM5 regulator/hose.
●   Also available with an Optional Needle Control Valve with Orifice.


●  Pipe Burner Video


                                                       
                                                       Weight w/ GS    Weight w/ GS & LEGS
●   PBM125-32" has 24" of flame           12#                 14#
●   PBM125-44" has 36" of flame           16#                 18#
●   PBM125-56" has 48" of flame           20#                 22#
●   PBM125-68" has 60" of flame           24#                 26#

If you would like TejasSmokers.com to weld permanent 1/2" diameter round support legs along the length of your pipe burner, then order the unit with "LEGS" at the end of the part number, as shown in the optional drop down box to the right.


Free shipping within the 48 contiguous U.S. States.

 

  • 32in Pipe Burner with Grease Shield and Support Legs
    32" Pipe Burner with Grease Shield and Optional Support Legs

 

$249.95

 

 

PBM-MODIFY - Custom Length Pipe Burner Modification

  PBM-MODIFY

PBM-MODIFY - Custom Length Pipe Burner Modification

There is a $25.00 charge for custom length modifications of pipe burners to shorten them from one of the stocked sizes.

If you need a 31" pipe burner, for example, you should purchase a 32" stocked unit (with or without a grease shield) and we will shorten the pipe and weld a 1/8" thick round steel plate on the end.  Such reductions in length come from the flame length section of the pipe and not the smooth "throat" region near the venturi. Refer to the picture at right to see how a custom length end would look.

$25.00

 

 

CVO - Control Valve  Orifice Fitting  , MNPT x 3/8" MGF

  CVO

CVO - Control Valve Orifice for 1/8", 1/4", or 3/8" NPT Burner Gas Inlet.
 


Why would I need a gas burner Control Valve Orifice?

The CVO250 needle control valve orifice allows one to adjust the height of the burner flames directly at the venturi rather than further back at the propane tank regulator or the natural gas source. This Control Valve Orifice fitting will work on practically any gas burner if the orifice is drilled to the proper size and you know the size of the gas inlet thread (1/8" or 1/4").

Indicate your fuel preference of either natural gas, low pressure propane, or high pressure propane in the Comments section in the Shopping Cart. The default orifice size is #61 for High Pressure propane.  However, we will drill it to the proper orifice size for your particular fuel. No extra charge.


Free shipping to the 48 contiguous U.S. States.
 

  •  Control Valve Orifice (1/8 M NPT X 3/8 M GF)
    CVO125
    (1/8" M NPT X 3/8" M GF)
  • Control Valve Orifice (1/4 M NPT X 3/8 M GF)
    CVO250
    (1/4" M NPT X 3/8" M GF)

  • Shown below is a CVO needle valve control on a straight pipe burner:
  • Pipe Burner with Grease Shield and Control Valve Orifice

 

 

$19.95

 

 

LPCAST - Low Pressure or Natural Gas, Cast Iron Burner with 6" Neck

  LPCAST

LPCAST - Low Pressure or Natural Gas Cast Iron Burner with 6" Neck

●  Produces up to 40,000 BTU/hr in an evenly-directed manner.
●  It comes with an air shutter, Insect Guard and a 90° 3/8" flare Orifice.
    Alternatively, a 180° 3/8" flare orifice fitting is also available on request

●  Best working distance is 2" from top of cast to bottom of pot.

●  There is a bottom center bolt which is a 6mm in diameter or a 1/4".
  From the center bolt to the air inlet at the edge of the burner is 6".
●  From the center bolt to the end of the orifice is approximately 7".
●  Total length of the burner with an orifice is approximately 10".
●  Burner head diameter is 6", height from base to top of burner is 2 1/2".
●  It has three 1 1/4" small legs at the bottom to stand the burner in place.

●  Natural Gas version available by request at the same price.
●  We recommend the use of a COM5 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.


Weight 3# 2 oz. Free shipping within the 48 contiguous U.S. States.

 

  • 40,000 BTU/hr Low Pressure or Natural Gas Cast Iron Burner with 6in Neck   40,000 BTU/hr Low Pressure or Natural Gas Cast Iron Burner with 6in Neck
    LPCAST with Optional Needle Valve Orifice
  • 40,000 BTU/hr Low Pressure or Natural Gas Cast Iron Burner with 6in Neck   40,000 BTU/hr Low Pressure or Natural Gas Cast Iron Burner with 6in Neck
    Bottom view of the LPCAST

 

 

$34.95

 

 

LPCAST-2 - Low Pressure or Natural Gas, 2- Part Burner w/Adj. Neck

  LPCAST-2

LPCAST-2 - Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck
 

 Produces up to 40,000 BTU/hr in an evenly-directed manner.
 
Burner ideal for applications where the venturi is placed outside or
    farther away from the area where the burner is placed.

●  Distance between burner head and venturi determined by length of 
    1/2" black pipe nipple used
.  Pipe nipple is NOT included.

●  Best working distance is 2" from top of cast to bottom of pot.

●  Burner head has 1/2" female normal pipe thread inlets.
●  Venturi has 1/2" FNPT adapter.
●  Comes with an air shutter, Insect Guard, and a 90° 3/8" flare Orifice.
    A 180° 3/8" flare fitting is also available upon request.
●  The burner head has a bottom center bolt which is a 6mm in diameter
●  Burner head diameter is 6", height from base to top of burner is 2 1/2"

●  Natural Gas version available by request at the same price.
●  We recommend the use of a COM5 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.


Weight 4# 8 oz. Free shipping within the 48 contiguous U.S. States.

 

  • 40,000 BTU/hr Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck   40,000 BTU/hr Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck
    LPCAST-2 with Optional Needle Valve Orifice
  • Bottom view of the LPCAST-2 40,000 Btu burener
    Bottom view of the LPCAST-2

 

$42.95

 

 

LPCAST8-2 - Low Pressure or Natural Gas, 2-Part  Burner w/Adj. Length Neck

  LPCAST8-2

LPCAST8-2  - Low Pressure or Natural Gas Two-Part
Cast Iron Burner - Adjustable Length Neck


 Produces up to 80,000 BTU/hr in an evenly-directed manner.
●  Designed for cooks who want more btu/hr from a low pressure cast.
  A unique burner ideal for applications where the venturi is needed to
    be placed farther away from the burner. Minimum distance of 4".

●  Flame can be controlled down to a low simmer.
●  Best working distance is 2" from top of cast to bottom of pot.

●  The distance between the burner head and venturi is determined by
    the length of the 1 1/4" black pipe nipple used
. Pipe nipple must be
    at least 4" long.  Pipe nipple NOT included.
●  Burner head and venturi have 1 1/4" female normal pipe thread inlets.
●  It comes with an air shutter, Insect Guard and a 90° 3/8" flare Orifice.
    A 180° 3/8" flare fitting is also available upon request.
●  It has four 6mm bolts to the sides of the burner, to mount the burner.
●  Burner head diameter is 8", height from base to top of burner is 6".

●  Natural Gas version available by request at the same price.
●  We recommend the use of a COM5 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.


Weight 11# 10 oz. Free shipping within the 48 contiguous U.S. States. 

 

  • 80,000 BTU/hr Low Pressure or Natural Gas Two-Part  Cast Iron Burner - Adjustable Length Neck
    LPCAST8-2
  • 80,000 BTU/hr Low Pressure or Natural Gas Two-Part  Cast Iron Burner - Adjustable Length Neck
    LPCAST8-2 with Optional CVO250
  • 80,000 BTU/hr Low Pressure or Natural Gas Two-Part  Cast Iron Burner - Adjustable Length Neck  80,000 BTU/hr Low Pressure or Natural Gas Two-Part  Cast Iron Burner - Adjustable Length Neck
    Bottom view of the LPCAST8-2
  • 80,000 BTU/hr Low Pressure or Natural Gas Two-Part  Cast Iron Burner - Adjustable Length Neck   80,000 BTU/hr Low Pressure or Natural Gas Two-Part  Cast Iron Burner - Adjustable Length Neck
    Novel design of LPCAST8-2 casting permits a pipe nipple of any length to enter from below

 

 

$115.95

 

 

LPCAST10 - Low Pressure or Natural Gas, Cast Iron Burner with 10" Neck

  LPCAST10

LPCAST10 - Low Pressure or Natural Gas Cast Iron Burner with 10" Neck

●  Produces up to 100,000 BTU/hr in an evenly-directed manner.

●  Flame can be controlled down to a low simmer.
●  It comes with an air shutter, Insect Guard and a 90° 3/8" flare Orifice.
    Alternatively, a 180° 3/8" flare orifice fitting is also available on request

●  Best working distance is 2" from top of cast to bottom of pot.

●  It has four 8mm bolts to the sides of the burner, to mount the burner.
  From the center burner to the air inlet at the edge of the burner is 10".
●  From the center bolt to the end of the orifice is approximately 11".
●  Total length of the burner with an orifice is approximately 17".
●  Burner head diameter is 10", height from bottom to top of burner is 5".

●  Natural Gas version available by request at the same price.
●  We recommend the use of a COM5 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.


Weight 13# 8 oz. Free shipping within the 48 contiguous U.S. States.






  • 100,000 BTU/hr Low Pressure or Natural Gas Cast Iron Burner with 10in Neck   100,000 BTU/hr Low Pressure or Natural Gas Cast Iron Burner with 10in Neck
    LPCAST10 with Optional Needle Valve Orifice
  • 100,000 BTU/hr Low Pressure or Natural Gas Cast Iron Burner with 10in Neck   100,000 BTU/hr Low Pressure or Natural Gas Cast Iron Burner with 10in Neck
    Bottom view of the LPCAST10
  • 100,000 BTU/hr Low Pressure or Natural Gas Cast Iron Burner with Pilot Assembly   100,000 BTU/hr Low Pressure or Natural Gas Cast Iron Burner with Pilot Assembly
    Pilot Light Assembly is available as an Option at additional charge (Go to bottom of page)

 

$97.95

 

 

LPCAST10-2 - Low Pressure or Natural Gas, 2-Part Burner w/Adj. Length Neck

  LPCAST10-2

LPCAST10-2 - Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck

 Produces up to 100,000 BTU/hr in an evenly-directed manner.
●  Flame can be controlled down to a low simmer.
  This unique burner is ideal for applications where the venturi is needed
     to be placed farther away from the burner.  Minimum distance of 4".

●  Distance between burner head and venturi is determined by the length
    of the 1 1/4" black pipe nipple used
.  Pipe nipple is NOT included.

●  Best working distance is 2" from top of cast to bottom of pot.

●  Burner head and venturi have 1 1/4" female normal pipe thread inlets.
●  It comes with an air shutter, Insect Guard and a 90° 3/8" flare Orifice.
    A 180° 3/8" flare fitting is also available upon request.
●  It has four 8mm bolts to the sides of the burner, to mount the burner.
●  Burner head diameter is 10", height from base to top of burner is 5".

●  Natural Gas version available by request at the same price.
●  We recommend the use of a COM5 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.


Weight 14# 8 oz. Free shipping within the 48 contiguous U.S. States.

 

  • 100,000 BTU/hr Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck   100,000 BTU/hr Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck
    LPCAST10-2 with Optional Needle Valve Orifice
  • 100,000 BTU/hr Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck
    Bottom view of the LPCAST10-2
  • 100,000 BTU/hr Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck
    LPCAST10-2

 

$127.95

 

 

LPCAST12-2 - Low Pressure or Natural Gas, 2-Part Burner w/Adj. Length Neck

  LPCAST12-2

LPCAST12-2 - Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck

 Produces up to 120,000 BTU/hr in an evenly-directed manner.
    Highest btu/hr cast burner for natural gas available.

●  Flame can be controlled down to a low simmer.
  This unique burner is ideal for applications where the venturi is
    needed to be placed farther away from the burner.

●  Distance between burner head and venturi is determined by the length
    of the 1 1/4" black pipe nipple used
.  Pipe nipple is NOT included.

●  Best working distance is 2" from top of cast to bottom of pot.

●  Burner head and venturi have 1 1/4" female normal pipe thread inlets.
●  It comes with an air shutter, Insect Guard and a 90° 3/8" flare Orifice.
    A 180° 3/8" flare fitting is also available upon request.
●  It has three 1 1/2" small legs at the bottom to stand the burner in place.
●  There are three bolts one on each leg which are 6mm in diameter.

●  Burner head diameter is 12", height from base to top of burner is 3 1/2".


●  Casting has provision for holding a pilot light or thermostat control.
●  Natural Gas version available by request at the same price.
●  We recommend the use of a COM5 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.


●  LPCAST12-2 with Pilot Light Assembly Video

Weight 19#. Free shipping within the 48 contiguous U.S. States.

 

  • 120,000 BTU/hr Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck     LPCAST12-2 with Optional Needle Valve
    LPCAST12-2 with Optional Needle Valve
  • 120,000 BTU/hr Low Pressure or Natural Gas Two-Part Cast Iron Burner - Adjustable Length Neck
    Bottom view of the LPCAST12-2
  • 120,000 Btu Burner Low Pressure or Natural Gas
    LPCAST12-2
  • 120,000 Btu Burner Low Pressure or Natural Gas with Pilot Assembly   120,000 Btu Burner Low Pressure or Natural Gas with Pilot Assembly
    Pilot Light Assembly is available as an Option at additional charge (Go to bottom of page)

 

$129.95

 

 

GRILL-2 - Low Pressure or Natural Gas, 2-Part Rectangular Burner 

  GRILL-2

GRILL-2 - Low Pressure or Natural Gas Two-Part Cast Rectangular Iron Burner - Adjustable Length Neck

●  Produces up to 70,000 BTU/hr in an evenly-directed manner.
●  Ideal for smoke houses, griddles and direct grills with grease shields.

  Burner ideal for applications where the venturi is placed outside or
    farther away from the area where the burner is installed.

  Distance between burner head and venturi is determined by length
    of the 3/4" black pipe nipple used. P
ipe nipple is NOT included.

●  Best working distance is 2" from top of cast to bottom of pot.

●  Burner head and venturi have 3/4" female normal pipe thread inlets.
●  It comes with an air shutter, Insect Guard and a 90° 3/8" flare Orifice.
    A 180° 3/8" flare fitting is also available upon request.
●  Burner head is 6" X 16", height from base to top of burner is 2 1/2".


●  Casting has provision for holding a pilot light or thermostat control.
●  Natural Gas version available by request at the same price.
●  We recommend the use of a COM5 regulator/hose.
●  Also available with an Optional Needle Control Valve with Orifice.


Weight 9#.   Free shipping within the 48 contiguous U.S. States. 
 

  • 70,000 BTU/hr Low Pressure or Natural Gas Two-Part Cast Rectangular Iron Burner - Adjustable Length Neck
  • 70,000 BTU/hr Low Pressure or Natural Gas Two-Part Cast Rectangular Iron Burner - Adjustable Length Neck
    GRILL2 with Optional Needle Valve Orifice
  •  Bottom view of the 70,000 Btu Grill2 Burner Head
    Bottom view of the Grill2 Burner Head
  • 70,000 Btu/hr Low Pressure Two Part Cast Iron Burner with Pilot Assembly
    Pilot Light Assembly is available as an Option at additional charge (Go to bottom of page)

 

$127.95

 

 

PILOT - Pilot Light Assembly

  PILOT

PILOT - Pilot Light Assembly

● Designed to be used with any cast burner.
● Consists of a needle or ball valve to control the gas flow for the burner,
   a tee with an adapter for incoming gas, a small 1/4" brass pipe after
   the tee to connect to a 90° elbow, another needle valve to control
   the gas flow for the pilot head and a 24" aluminium pilot tubing
   with a pilot head install.
● In stock we have 1/4", 3/8", 1/2", 3/4", 1 1/4" Female NPT.

●  LPCAST12-2 with Pilot Light Assembly Video



Wt. 1# 2oz.    Free shipping within the 48 contiguous U.S. States.
 

  • 1/4 Pilot Light Assembly  1/4 Pilot Light Assembly
    1/4" Pilot Light Assembly
  • 3/8 Pilot Light Assembly   3/8 Pilot Light Assembly
    3/8" Pilot Light Assembly
  • 1/2 Pilot Light Assembly   1/2 Pilot Light Assembly
    1/2" Pilot Light Assembly
  • 3/4 Pilot Light Assembly   3/4 Pilot Light Assembly
    3/4" Pilot Light Assembly
  • 1 1/4 Pilot Light Assembly   1 1/4 Pilot Light Assembly
    1 1/4" Pilot Light Assembly

 

$59.95

 

 

INSECT1 -  Insect Guard Screen, 2 1/2" Diameter

  INSECT1

INSECT1 -  Insect Guard Screen, 2 1/2" Diameter Small Screen

● This screen helps prevent insects from nesting inside cast iron burner,
   on the air inlet part. It is standard on the following burners that we stock:

   HPOCA4, HPB6, HPCAST6, HPGX-1, HPGX-2
   LPCAST, LPCAST-2, GRILL-2


● If you are purchasing a burner from us then there is no need to
   purchase a Insect Guard since is already included in the burner.

● Diameter of Insect Guard is approxiately 2 1/2".

Wt. 1 oz.   Free shipping within the 48 contiguous U.S. States.

$2.95

 

 

INSECT2 - Large  Insect Guard Screen, 3 1/2" Diameter

  INSECT2

INSECT2 - Large Insect Guard Screen, 3 1/2" Diameter Large Screen

● This screen helps prevent insects from nesting inside cast iron burner,
   on the air inlet part. It is standard on the following burners that we stock:

   HPMAX-1, HPMAX-2, LPCAST8-2,
   LPCAST10, LPCAST10-2, LPCAST12-2


● If you are purchasing a burner from us then there is no need to
   purchase a Insect Guard since is already included in the burner.

● Diameter of Insect Guard is approxiately 3 1/2".


Wt. 1 oz.   Free shipping within the 48 contiguous U.S. States.

$2.95

 

 

Our Cast Burners are popular with home brewers because they work dependably right from the start.  The castings are clean and don't leak.  Poor quality, cheap castings can end up costing a lot of time, money, damage, and aggravation.  High quality Propane Cast Burners from Tejas Smokers®  simply work well and are shipped free to North Carolina, South Carolina, Georgia, Mississippi, Tennessee, Louisiana - all the 48 contiguous U.S.States.