Home  >  Pipe Burners

 

Pipe Burners are used in hog roasters as well as in a variety of commercial applications.  Our pipe burners are made with care and are bench tested to insure that they self-light and give even levels of blue flames from one end to the other. We build them for use with high pressure propane, low pressure propane, or for use with natural gas. Give us a call about your project. We can help.

 

PBM125 - Pipe Burner - (support LEGS are an option)

  PBM125

PBM125 - Straight Pipe Burner 1 1/4" ID - 32", 44", 56", or 68" lengths.

  • We stock 32", 44", 56", and 68" pipe burner assemblies, also called stick burners or tube burners, (as measured from one end of the pipe to the opposite end of the pipe's threads.)
  • The pipe burners are 1.25"ID and 1.5"OD with a standard schedule 40 pipe wall thickness. These assemblies include a welded end cap at one end and a venturi at the other end.
  • For supporting the assembly we recommend a cradle out of a well supported length of angle iron. A cradle support will permit easy removal of the burner unit for cleaning, when necessary.
  • Our pipe burners have been engineered and tested to give a even, high heat blue flame across the length of the pipe and they easily light.
  • The first 8" of the pipe is used as the "throat" of the burner and does not have any holes for flames. This space is required for the air and gas to mix efficiently in order to have a nice blue flame. Don't waste propane using a pipe burner that burns an inefficient yellow flame.

●   PBM125-32" has 24" of flame         8#                  10#
●   PBM125-44" has 36" of flame       10#                  12#
●   PBM125-56" has 48" of flame       12#                  15#
●   PBM125-68" has 60" of flame       15#                  18#

If you would like  TejasSmokers.com  to weld permanent 1/2" diameter round support legs along the length of your pipe burner then order the unit with "LEGS" at the end of the part number, as shown in the drop down box at right.

                       Free shipping within the 48 contiguous U.S. States.

 

  • 68" Pipe Burner with 1 1/4" FNPT Venturi and Optional Control Valve Orifice (Needle Valve)

  • 32in Pipe Burner with Support Legs

    32" Pipe Burner with Optional Support Legs

  • 32in Pipe Burner with Optional Support Legs and Pilot Assembly
  • 32in Pipe Burner with Optional Support Legs and Pilot Assembly

T-PILOT Assembly is available as an Option at additional charge

If you would like to automate your pipe burner or any cast iron burner setup to use a pilot light,or a piezo electric ignitor, or a automatic thermostat controller, or a safety valve then give us a call at 713.222.0077. We can help you do it.


 

$219.95

 

 

PBMG125 - Pipe Burner with Grease Shield - (support LEGS are an option)

  PBMG125

PBMG125 - Straight Pipe Burner 1 1/4" ID in 32", 44", 56", or 68" lengths with a permanently welded 3" high grease shield.

  • We stock 32", 44", 56", and 68" pipe burners assemblies.(As measured from one end of the pipe to the opposite end of the pipe's threads.)
  • The pipe burners are 1.25"ID and 1.5"OD with a standard schedule 40 pipe wall thickness. These assemblies include a welded end cap at one end and a venturi at the other end.
  • For supporting the assembly we recommend a cradle out of a well supported length of angle iron. A cradle support will permit easy removal of the burner unit for cleaning, when necessary.
  • Our pipe burners have been engineered and tested to give a even, high heat blue flames across the length of the pipe and they easily light.
  • The first 8" of the pipe is used as the "throat" of the burner and does not have any holes for flames. This space is required for the air and gas to mix efficiently in order to have a nice blue flame. Don't waste propane using a pipe burner that burns an inefficient yellow flame.

●   PBM125-32" has 24" of flame           12#                         14#
●   PBM125-44" has 36" of flame           16#                         18#
●   PBM125-56" has 48" of flame           20#                         22#
●   PBM125-68" has 60" of flame           24#                         26#

If you would like TejasSmokers.com to weld permanent 1/2" diameter round legs to support your pipe burner, then order the unit with "LEGS" at the end of the part number, as shown in the optional drop down box at right.
                          Free shipping within the 48 contiguous U.S. States.


                         32" Pipe Burner with Grease Shield and Optional Support Leg

                                              
                                      Pipe Burner with Optional T-PILOT Assembly

 

$249.95

 

 

PBM-MODIFY - Custom Length Pipe Burner Modification

  PBM-MODIFY

PBM-MODIFY - Custom Length Pipe Burner Modification.

There is a $25.00 charge for custom length modifications of pipe burners to shorten them from one of the stocked sizes.


If you need a 31" pipe burner, for example, you should purchase a 32" stocked unit (with or without a grease shield) and we will shorten the pipe and weld a 1/8" thick round steel plate on the end. Such reductions in length come from the flame length section of the pipe and not the smooth "throat" region near the venturi. Refer to photo at right to see how a custom length end would look.

$25.00

 

 

Tejas Smokers® ships Pipe Burners freight free to North Carolina, South Carolina, Georgia, Florida, California and all other 48 contiguous U.S. States.