:: Search Products ::

Home > Search Result >

Home > Search Result > Products

T-PILOT - Gas Needle Valve Dual Needle Valve Gas Burner Pilot and Complete Assembly

T-PILOT

T-PILOT - Gas Burner Pilot Light, complete burner pilot and burner control assembly with dual needle valves, 24" of gas tubing, stainless steel pilot light head, stainless steel zip ties, gas inlet fitting, burner gas orifice fitting.

► Our proprietary dual Gas Needle Valve for use with any burner, tell us the burner type in COMMENTS in the Shopping Cart.

► Includes dual needle valve gas burner controls for fine control of pilot light and burner head, 24” of aluminum gas pilot light tubing, two stainless steel zip ties, burner orifice fitting, gas flare gas-inlet fitting.

► A precision machined brass gas burner control fitting.

► Select 1/8" MNTP or 1/4" MNPT for your gas burner inlet.
► Knurled brass control knob, valve rated at 350 PSI

► Wt. 12 oz. (complete assembly). Free shipping to the 48 U.S. States.

Gas Burner Pilot Assembly
Pilot Assembly on Low Pressure Burner

HPB6 high pressure burner with PILOT
HPMAX-2 high pressure burner with PILOT

Easy installation on almost any cast burner, pipe burner, propane jet burner, torch,tarpot, gas fired kiln, furnace, weed burner, blacksmith forge, or multiple burner manifold

$79.95

Pilot Light Dual Needle Valve Complete Pilot and Gas Burner Control Assembly

T-PILOT

► Our proprietary dual Gas Needle Valve for use with any burner, tell us the burner type in COMMENTS in the Shopping Cart.

► A precision machined brass gas burner control fitting.

► Select 1/8" MNTP or 1/4" MNPT for your gas burner inlet.

► Knurled brass control knob, valve rated at 350 PSI

Wt. 12 oz. (complete assembly). Free shipping to the 48 U.S. States.

$79.95

T-PILOT - Gas Needle Valve - Dual Needle Valve Gas Burner Pilot and Complete Assembly

HPOCA4 - High Pressure Cast Iron Propane Burner with 4" Neck

HPOCA4

HPOCA4 - High Pressure Cast Iron Propane Burner with a shorter 4" Neck

Produces up to 160,000 BTU/hr in an evenly-directed manner.
Includes air shutter, Insect Screen Guard, and a 90° 3/8" flare Orifice.Alternatively, a 180° 3/8" flare orifice fitting is also available.
Best working distance is 3" to 4" from top of cast to bottom of pot.

The center bolt is a 6mm in diameter or a 1/4".
From the center bolt to the air inlet at the edge of the burner is 5".
Best working distance is 3" to 4" from top of cast to bottom of pot.
From the center bolt to the end of the orifice is approximately 6".
Total length of the burner with an orifice is approximately 8".
Burner head diameter is 4", height from base to top of burner is 3".

We recommend the use of a COM3 regulator/hose.
Available with an Optional CVO Needle Control Valve with Orifice.
Also available with a T-PILOT Assembly.

Weight 3# 13 oz. Free shipping within the 48 contiguous U.S. States.

HPOCA4 with Optional Control Valve Orifice Bottom side view of the HPOCA4

Bottom side view of the HPOCA4

HPOCA4 with Optional T-PILOT for the burner

$39.95

Cast-Iron-Propane-Burner-with-4-inch-Neck

PBM125 - Pipe Burner - support LEGS are an option

PBM125

PBM125 - Straight Pipe Burner 1 1/4" ID - 32", 44", 56", or 68" lengths.

We stock 32", 44", 56", and 68" pipe burner assemblies, also called stick burners or tube burners, (as measured from one end of the pipe to the opposite end of the pipe's threads.)
The pipe burners are 1.25"ID and 1.5"OD with a standard schedule 40 pipe wall thickness. These assemblies include a welded end cap at one end and a venturi at the other end.
For supporting the assembly we recommend a cradle out of a well supported length of angle iron. A cradle support will permit easy removal of the burner unit for cleaning, when necessary.
Our pipe burners have been engineered and tested to give a even, high heat blue flame across the length of the pipe and they easily light.
The first 8" of the pipe is used as the "throat" of the burner and does not have any holes for flames. This space is required for the air and gas to mix efficiently in order to have a nice blue flame. Don't waste propane using a pipe burner that burns an inefficient yellow flame.

Pipe Burners can be run by High Pressure Propane, Low Pressure Propane, or Natural Gas. Indicate your fuel in the COMMENTS section.
For High Pressure use we recommend the COM3 regulator/hose.
For Low Pressure use we recommend the COM5 regulator/hose.
The Optional CVO Needle Control Valve with Orifice.
Also available with a T-PILOT Assembly.
Pipe Burner Video Weight Weight w/LEGS

●   PBM125-32" has 24" of flame      8# 10#
●   PBM125-44" has 36" of flame    10# 12#
●   PBM125-56" has 48" of flame    12#    15#
●   PBM125-68" has 60" of flame    15#    18#

If you would like TejasSmokers.com to weld permanent 1/2" diameter round support legs along the length of your pipe burner then order the unit with "LEGS" at the end of the part number, as shown in the drop down box at right.

We can custom fabricate stainless steel pipe burners in any length on our milling machine. Call for a quote.

Free shipping within the 48 contiguous U.S. States.

68" Pipe Burner with 1 1/4" FNPT Venturi and Optional Control Valve Orifice (Needle Valve)
32" Pipe Burner with Optional Support Legs

T-PILOT Assembly for the pipe burner is available as an Option at additional charge

$299.95

PBMG125 - Pipe Burner with Grease Shield - (support LEGS are an option)

PBMG125

PBMG125 - Straight Pipe Burner 1 1/4" ID in 32", 44", 56", or 68" lengths with a permanently welded 3" high grease shield.

We stock 32", 44", 56", and 68" pipe burners assemblies.(As measured from one end of the pipe to the opposite end of the pipe's threads.)
The pipe burners are 1.25"ID and 1.5"OD with a standard schedule 40 pipe wall thickness. These assemblies include a welded end cap at one end and a venturi at the other end.
For supporting the assembly we recommend a cradle out of a well supported length of angle iron. A cradle support will permit easy removal of the burner unit for cleaning, when necessary.
Our pipe burners have been engineered and tested to give a even, high heat blue flames across the length of the pipe and they easily light.
The first 8" of the pipe is used as the "throat" of the burner and does not have any holes for flames. This space is required for the air and gas to mix efficiently in order to have a nice blue flame. Don't waste propane using a pipe burner that burns an inefficient yellow flame.

For High Pressure we recommend the COM3 regulator/hose.
For Low Pressure use we recommend the COM5 regulator/hose.
The Optional CVO Needle Control Valve with Orifice.
Also available with a T-PILOT Assembly.
Pipe Burner Video Weight w/ GS Weight w/ GS & LEGS

●   PBM125-32" has 24" of flame 12# 14#
●   PBM125-44" has 36" of flame 16# 18#
●   PBM125-56" has 48" of flame 20# 22#
●   PBM125-68" has 60" of flame 24# 26#

If you would like TejasSmokers.com to weld permanent 1/2" diameter round legs to support your pipe burner, then order the unit with "LEGS" at the end of the part number, as shown in the optional drop down box at right.
Free shipping within the 48 contiguous U.S. States.

32" Pipe Burner with Grease Shield and Optional Support Leg

Pipe Burner with Optional T-PILOT Assembly

$349.95

PBM125-32 Custom Pipe Burner with Optional Control Valve Orifice

A75AM - 3/4" Cast Aluminum Venturi Air Gas Mixer, with an air shutter, Insect Screen Guard, and the selected orifice fitting.

A75AM

New Venturi Design

A75AM 3/4" Cast Aluminum Venturi Air Gas Mixer, air shutter, with Insect Screen Guard, and a 90° 3/8" gas flare orifice fitting (or selected orifice type).

- Aluminum Casting Made in Houston, Texas. Made-in-U.S.A.

- It has a 3/4" Female Normal Pipe Thread Outlet.

- Light Weight, No Paint Needed and No Rust.

- To be used with High Pressure / Low Pressure Propane or
Natural Gas.

- The flat top surface is 3" in diameter by 1-3/4" in height.

- The height of the venturi with an orifice is approximately 2-3/4".

- Includes an Aluminum Air Shutter, Insect Screen Guard and a
90 3/8" Flare Orifice, with #61 Orifice for High Pressure Propane.

- Alternatively, a 180 3/8" Flare Orifice fitting is also available.
- Drilled to custom orifice size depending on your specified fuel and
length of pipe burner or specified burner at No Extra Charge.

(For alternative orifice or custom drilled orifice please let us know the
information in comment box section when added to shopping cart).

For High Pressure use we recommend the COM3 regulator/hose.
For Low Pressure use we recommend the COM5 regulator/hose.
The Optional CVO Needle Control Valve with Orifice.
Also available with a T-PILOT Assembly.

Weight 7 oz. Free shipping within the 48 contiguous U.S. States.

3/4
3/4" Female NPT outlet threads.

The photos below show the different Options which can be choosen from the drop-down menu above the price.

OPTIONS:

A75AM - 3/4
A75AM with 90° Orifice, $99.95

A75AM with CVO Valve Orifice, $139.95

A75AM with T-PILOT Assembly, $179.95

$99.95

A75AM 3/4" Cast Aluminum Venturi Air Gas Mixer, air shutter, with Insect Screen Guard, and a 90° 3/8" gas flare orifice fitting

LPCAST6-2 - Low Pressure Propane or Natural Gas 2-Part Burner, 6" x 6" Sqaure Burner Head with Adjustable Lenght Neck

LPCAST6-2

NEW BURNER /
NEW DESIGN

LPCAST6-2 - Low Pressure Propane or Natural Gas Two-Part Burner

Perfect for Smoker Pits and Smoke Houses.

- Made in Houston, Texas. Made-in-U.S.A.

- 40,000 BTU/hr Output

- 6" x 6" Burner Head

- Aluminum Casting Air and Gas Mixer Venturi

- Set Up for Low Pressure Propane Or Natural Gas

- Two-Part Burner, Pipe Nipple NOT Included

- NEW Design from our our LPCAST-2 Burner

( Similar to our old LPCAST-2 Burner but a better Upgrade)

- LPCAST-2 Video Reference

Top View of Burner Head

Bottom View of Burner Head Side View of Burner Head

3/4" Female NPT Threads

LPCAST6-2 Burner OPTIONS:

LPCAST6-2 with 90 Degree Orifice, $ 259.95

LPCAST6-2 with CVO Needle Control Valve Orifice, $ 299.95

LPCAST6-2 with T-Pilot Assembly, $ 339.95

$259.95

LPCAST6-2 - Low Pressure Propane or Natural Gas 2-Part Burner, 6" x 6" Sqaure Burner Head with Adjustable Lenght Neck

HPCAST6 - High Pressure Cast Iron Propane Burner with 6 inch Neck

HPCAST6

HPCAST6 - High Pressure Cast Iron Propane Burner with a 6" Neck.

Produces up to 160,000 BTU/hr in an evenly-directed manner.
Includes an air shutter, Insect Screen Guard and a 90° 3/8" flare Orifice. Alternatively, a 180° 3/8" flare orifice fitting is also available.
Best working distance is 3" to 4" from top of cast to bottom of pot.

The center bolt is a 6mm in diameter or a 1/4".
From the center bolt to the air inlet at the edge of the burner is 6 1/2"
From the center bolt to the end of the orifice is approximately 7 1/2"
Total length of the burner with an orifice is approximately 10".
Burner head diameter is 4", height from base to top of burner is 3"

We recommend the use of a COM3 regulator/hose.
Available with an Optional CVO Needle Control Valve with Orifice.
Also available with a T-PILOT Assembly.

Weight 3# 8 oz. Free shipping within the 48 contiguous U.S. States.

HPCAST6 with Optional Control Valve Orifice

Bottom side view of the HPCAST6

HPCAST6 with Optional T-PILOT Assembly for the burner

$59.95

HPCAST6 - Cast Iron Propane Burner with a 6 inch Neck

HP12 - Single Burner Hot Plate Cooker with 12" diameter 120,000 btu/hr Burner, Low Pressure or Natural Gas

HP12

HP12 - Single Burner Hot Plate Cooker with 12" diameter 120,000 btu/hr Burner, choose Low Pressure or Natural Gas.

This is a new high heat burner of our own design. It is the highest btu/hr cast iron burner for natural gas use on the market today. The only way to get more btu/hr from a natural gas burner is to use a jet burner. Designed for the cooks who really want to use Natural Gas and have been frustrated by the current btu/hr heat limits of the burners available on the market.

We recommend the use of a COM5 low pressure propane regulator. Contact us for natural gas hoses, which we stock in many lengths. This new casting also has the ability to accept a T-PILOT Assembly. Many accessory options are found at the bottom of this page.

Wt. 38#. Free shipping within the 48 contiguous U.S. States.

An Amazing 120,000 btu/hr Using Natural Gas or Low Pressure Propane

$700.00

Single Burner Hot Plate Cooker with 120,000 btu/hr Burner

CS1-COM - Single Burner Portable Outdoor Camping Cooker Stand COMBO For Outdoor Cooking, Camping, Wok Cooking, and Picnics

CS1-COM

CS1-COM -Single Burner Portable Outdoor Camping Cooker Stand COMBO, includes (2) WINGS, (1) Wind Guard, and Regulator Assembly. Choice of High Pressure, Low Pressure, or Natural Gas. For Outdoor Cooking, Wok Cooking, Camping, and Picnics

COMBO includes: CS1 series Single-Burner burner dual-height Cooker Stand, (2) WING Side Table Extensions, 8" high WG1 folding Wind Guard, propane regulator assembly with a 5 ft hose and Needle Control Valve at the burner. All you need is the propane tank. Natural gas version comes with a 60" natural gas hose and inline Needle Control Valve.

Wt. 46#. Free shipping within the 48 contiguous U.S. States.